thin walled tube中文是什么意思

• 薄壁管

• "thin"中文翻译    adj. (thinner; thinnest) 1.薄 ...
• "walled"中文翻译    adj. 1.有墙的，有围墙的。 2.设(防御)工事的。 ...
• "tube"中文翻译    n. 1.管，筒；颜料管。 2.管状地下隧道；〔口语〕( ...
• "thin-walled tube" 中文翻译 :    薄壁管
• "thin-walled tube sampler" 中文翻译 :    薄壁管取样器; 薄壳取样器
• "thin-walled" 中文翻译 :    薄壁的; 薄墙的
• "thin walled bar" 中文翻译 :    薄壁杆件
• "thin walled beam" 中文翻译 :    薄壁梁
• "thin walled bearing bush" 中文翻译 :    薄壁轴承衬
• "thin walled blast furnace" 中文翻译 :    薄炉身高炉
• "thin walled cell" 中文翻译 :    薄壁管胞
• "thin walled container" 中文翻译 :    薄壁盛料器
• "thin walled cylinder" 中文翻译 :    薄壁圆筒
• "thin walled fiber" 中文翻译 :    薄壁纤维
• "thin walled girder" 中文翻译 :    薄腹梁
• "thin walled metal mould" 中文翻译 :    薄壁金属型
• "thin walled mould" 中文翻译 :    薄壁结晶器
• "thin walled needle with stylet" 中文翻译 :    薄壁带鞘针
• "thin walled pipe" 中文翻译 :    薄壁管
• "thin walled polyethylene catheter" 中文翻译 :    薄壁聚乙烯导管
• "thin walled pressure vessel" 中文翻译 :    薄壁压力容器
• "thin walled sampler" 中文翻译 :    薄管采样器
• "thin walled section" 中文翻译 :    薄壁剖面
• "thin walled steel structure" 中文翻译 :    薄壁钢结构
• "thin walled structure" 中文翻译 :    薄壁结构

• Thin wall tube of nickel and nickel alloy
  镍及镍合金无缝薄壁管
• In this paper , thin wall tube initial yield under the pressure of hydraulic pressure , axial pressure , is discussed , the calculate formulae of initial deformation force is derived and experimental verification has been finished
  摘要本文就有限长薄壁管在内压、轴力作用下初始屈服问题进行了研究，推导出了初始力计算公式，并进行了实验验证。
• The numerical control ( nc ) tube bending process used as a method of thin walled tube bending has been widely applied in fields of aeronautics and astronautics . however , the process planning based on the traditional " trial - and - error " method limits the predominance of this advanced process
  数控弯管工艺在航空、航天工业的薄壁管弯曲成形中占有重要地位，但传统的基于经验和试验的工艺设计方法限制了数控弯管工艺优势的发挥。
• By the experiment of tension and torsion test of thin walled tube on mts , the experimental strain increment was obtained and compared with theoretical strain increment which obtained by simulation with m value 2 and the identified m value . the results of comparison validated the correctness of identified m and deformation control method using the identified m
  本文在mts实验机上进行了薄壁管拉扭实验，首先进行了识别材料物性参数m值的实验，通过实验中各阶段的实际应变增量值与m值识别前后计算所得理论应变增量值的比较，验证了识别所得m值的正确性以及根据识别所得m值进行应变控制可行性。
• Furthermore by the experiment of tension and torsion test of thin walled tube on mts equipment , the experimental strain path was obtained and compared with target strain path . the results of comparison validated the correctness of the approach of controlling deformation path
  其次，在正确识别材料物性参数m值的基础上进行了应变路径控制实验，通过实验过程中的实际应变路径与想要得到的目标应变路径的比较，验证了在正确识别材料物性参数前提下，基于数值模拟和神经网络的应变路径控制方法的正确性。